Not happy with the selection of sanding blocks at the hardware store, I made a few of my own from hardwood scraps left over from a woodworking project. I cut each one to 3/4 in. x 1-1/2 in. x 4-1/2 in.—which is just the right size to wrap a quarter sheet of sandpaper around. And the “kerf” cut helps hold the sandpaper in place until I’m ready to change it. —Tim Olaerts. Here are 41 more genius sanding tips you need to know.


Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many
Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves. 

Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster

If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.
Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.

There are a few things particleboard is NOT. It’s not medium density fiberboard (MDF)—a material with greater density and weight composed of more uniform particles. It’s NOT oriented strand board (OSB), a material composed of large wood chips and strands that’s structurally equivalent to plywood. It does NOT have great nail or screw holding ability, nor is it all that water resistant; water can quickly cause the material to swell and lose structural integrity. But if you need something flat and cheap for use in a dry place, particleboard will do you proud. Learn how to make a plastic laminate tabletop with a particleboard substrate.

woodworking plans

×