Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots.
This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!

Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.

​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Not happy with the selection of sanding blocks at the hardware store, I made a few of my own from hardwood scraps left over from a woodworking project. I cut each one to 3/4 in. x 1-1/2 in. x 4-1/2 in.—which is just the right size to wrap a quarter sheet of sandpaper around. And the “kerf” cut helps hold the sandpaper in place until I’m ready to change it. —Tim Olaerts. Here are 41 more genius sanding tips you need to know.
Hardwoods are separated into two categories, temperate and tropical hardwoods, depending on their origin. Temperate hardwoods are found in the regions between the tropics and poles, and are of particular interest to wood workers for their cost-effective aesthetic appeal and sustainable sources.[9] Tropical hardwoods are found within the equatorial belt, including Africa, Asia, and South America. Hardwoods flaunt a higher density, around 65lb/cu ft as a result of slower growing rates and is more stable when drying.[9] As a result of its high density, hardwoods are typically heavier than softwoods but can also be more brittle.[9] While there are an abundant number of hardwood species, only 200 are common enough and pliable enough to be used for woodworking.[11] Hardwoods have a wide variety of properties, making it easy to find a hardwood to suit nearly any purpose, but they are especially suitable for outdoor use due to their strength and resilience to rot and decay.[9] The coloring of hardwoods ranges from light to very dark, making it especially versatile for aesthetic purposes. However, because hardwoods are more closely grained, they are typically harder to work than softwoods. They are also harder to acquire in the United States and, as a result, are more expensive.[9]
Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.
Cutting sandpaper is a quick way to dull your scissors or utility knife blade. Instead, I fastened a hacksaw blade to the edge of my workbench. I slipped a washer behind the blade at each of the mounting holes so a sheet of sandpaper to easily slides in behind the blade. I fold the paper where I want to cut, just as a reference. — Kim Boley. Try some of these storage solutions!

The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.


Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
Tired of waiting for finish to dry on one side before finishing the other side? You can purchase standoffs, but it’s also really easy to make them yourself. Simply drive 2-in. drywall screws through 2-in. x 2-in. squares of 3/4-in. thick stock. The screw points will leave a divot in the finish that can be touched up later, but I always let the back side of my project rest on the screws while the finish dries. — Matt Boley. Plus: Check out these 32 other handy hints for frugal shop rats.
Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.
Popular and easy to work with, cherry is in high demand for its reddish-brown color and ease of staining and finishing. Cherry likely won’t be at the local home center, but should be at a lumberyard for a somewhat expensive price.[12] This hardwood is a very common material for furniture, and is resistant to normal wear-and-tear, but it is best for indoor pieces.[13]
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products
Sanding curves is tricky. Sometimes you need a sanding pad that’s both firm and flexible. A small notepad works great. Just wrap sandpaper around the pad and bend the pad to whatever arc you need. Slip the one end of the sandpaper between the pages to help hold it in place on the pad. Give this a try the next time you’re working on a project that has curves and tough to reach spots.
Often times at first glance a board looks straight and the fact that it is actually bowed or has some warping isn’t always obvious. So the trick to knowing for sure, is to hold the board up towards your face, with the other end on the ground, and look at it at a downward angle (as shown in the below photo). This method will allow you to see if it is bowing at all.
Here, I am writing about another DIY project that involves the use of an old furniture piece. I think that the idea of reusing and recycling old furniture has got to me. Anyways, I am starting to love it. This project involves using an old door to build a beautiful multi picture frame, as you can see in the image below. This frame looks really wonderful and can be used to hold many pictures at a time.
The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
The source above is not exactly a tutorial, but it gives you a basic idea of how the author built a Quirky Pallet Art to enhance the look of their old house. You can also find another tutorial at the link below. It shares a step by step procedure for making a wooden pallet sign. The final product is not exactly the same as the one above, but the basic idea is the same.
Sanding concave molding doesn’t have to be difficult. Find a deep socket that fits the contour of your molding. Wrap a piece of sand- paper around the socket and hold it in place with your fingers. Your sanding will be uniform and the delicate edges of the molding won’t round over. — Eric and Cheryl Weltlich. In this video, Travis talks about his favorite sanding tips.
A board is considered “quarter-sawn” when the growth rings run, more or less, perpendicular to the face of the board. Quarter-sawn boards generally have straight grain and are less prone to shrinkage, compared to other boards. These factors don’t come into play with the 2x4s you use to frame a closet—but it does with the shelves and cabinetry you put into that closet; you want those boards to remain straight, flat and stable.
Often times at first glance a board looks straight and the fact that it is actually bowed or has some warping isn’t always obvious. So the trick to knowing for sure, is to hold the board up towards your face, with the other end on the ground, and look at it at a downward angle (as shown in the below photo). This method will allow you to see if it is bowing at all.
×