Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!
If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.
The shelf in the first picture is made of red oak plywood. You can choose the wood type, color and design as you like for your project. In case if you need more help understanding this project, you can refer the source link below. It discusses various items used, steps and tips and personal experience of the author who personally built a Zigzag shelf.
Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!

Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
Second, learning how to read lumber dimensions, like knowing what 1×2 or 2×12 actually means, is really important. Understanding softwood lumber dimensions will help you to read woodworking build plans, shop for lumber, and understand the general measurements for your projects. I’ve provided a simple explanation to lumber sizes along with a free lumber size chart printable here!

Another wooden item that I love very much is a beautiful mobile holder. You can see one in the image below. These things are not only beautiful, but they can comfortably hold any sized mobile and ensure proper safety. Another amazing thing is that they can be built in many shapes and sizes, as and how you need it. You can see some more examples at the source below


I know this seems really simple and you may already know how to read a tape measure so just hear me out on this one! Often times with woodworking you need to make exact measurements and cuts and it’s rarely pretty even numbers like 15 inches or 15 1/2 inches. It’s usually like 15 5/8 inches or 15 9/16 inches. So, really knowing how to read a tape measure in its entirety is important. And I’ve created a quick post on how to read a tape measure the easy way along with a helpful free printable.

Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.


While many woods can be used for carving, there are some clear favorites, including Aspen, Basswood, Butternut, Black Walnut, and Oak.[14] Because it has almost no grain and is notably soft, Basswood is particularly popular with beginner carvers. It is used in many lower-cost instruments like guitars and electric basses.[14] Aspen is similarly soft, although slightly harder, and readily available and inexpensive.[14] Butternut has a deeper hue than Basswood and Aspen and has a nice grain that is easy to carve, and thus friendly for beginners. It's also suitable for furniture.[14] While more expensive that Basswood, Aspen, and Butternut, Black Walnut is a popular choice for its rich color and grain.[14] Lastly, Oak is a strong, sturdy, and versatile wood for carving with a defined grain. It's also a popular wood for furniture making.[14]


Can you believe that this amazing wine rack the image below has been built using old wood pallets? Perhaps you can. Isn’t it wonderful that your old wood pallets can be reused to build something so beautiful and useful? I am not a drinker but I liked the idea so much that I just couldn’t resist making myself one. Although later I gifted it to my parents, who totally loved it.
Fir, also known as Douglas Fir, is very inexpensive and common at local home centers. It has a characteristic straight, pronounced grain with a red-brown tint. However, its grain pattern is relatively plain and it does not stain well, so Fir is commonly used when the finished product will be painted. While commonly used for building, this softwood would also be suitable for furniture-making as well.[12]
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.
This is definitely going to be one of the easiest woodworking projects you’ll be reading about today. So why not just get started? The tutorial link is given below. Just do exactly what they are saying in the tutorial and you will end up making a beautiful wooden doormat just like the one in the image above. They are using pine wood to build this doormat. You can choose any wood material that best suits your budget.
The source above is not exactly a tutorial, but it gives you a basic idea of how the author built a Quirky Pallet Art to enhance the look of their old house. You can also find another tutorial at the link below. It shares a step by step procedure for making a wooden pallet sign. The final product is not exactly the same as the one above, but the basic idea is the same.
×