Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Tired of waiting for finish to dry on one side before finishing the other side? You can purchase standoffs, but it’s also really easy to make them yourself. Simply drive 2-in. drywall screws through 2-in. x 2-in. squares of 3/4-in. thick stock. The screw points will leave a divot in the finish that can be touched up later, but I always let the back side of my project rest on the screws while the finish dries. — Matt Boley. Plus: Check out these 32 other handy hints for frugal shop rats.
Although refrigerators long ago rendered them obsolete, antique oak ice boxes remain popular with collectors, even though they’re expensive and hard to find. This do-it-yourself version is neither: it’s both inexpensive and easy to build. An authentic reproduction of an original, the project is especially popular when used as a bar, but it has many
Having swing in your own home, yard or garden can be so de-stressing and be relaxing a thing to enjoy, that doesn’t matter you have a big yard or patio, or vacant porch. Kids will surely fall in love with this swing porch and love playing on a breezy day. Even, adults also do relax and enjoy a quite morning coffee, or just being embraced by the sun in the swing.
“I do a lot of finish-sanding freehand, without a sandpaper block, so I can smooth edges and get into nooks and crannies. But the finer grits are usually bonded to thinner paper and, at least for me, the paper is too thin and ends up tearing long before the grit wears out. So I apply duct tape to the back of the sandpaper. The sandpaper is still flexible enough to sand a tight radius and it’s far more durable. You can use this super-strong sandpaper like a shoeshine rag.” — Chuck Merchant
Here’s an easier way to stain or seal chairs, lattice or anything with numerous tight recesses. Pour the stain into a clean, empty spray bottle ($3). Spray the stain onto the project and wipe up the excess with a brush or rag. The sprayer will squirt stain into all those tight, hard-to-reach cracks and joints. — Valrie Schuster. Learn more about staining wood.
I’m 91 years old, but I still enjoy spending time in the wood shop. I like to make wooden toys and give them to my great-grandkids and charity groups. One trick I’ve learned over the years is to use emery boards—the kind for filing fingernails— to sand small parts. Emery boards come in different sizes, and some are more abrasive than others, so I keep an assortment on hand. — Joe Aboussleman
Sanding the inside of a hole or curved surface can be difficult. To simplify that task, insert a 1/4 x 3-in. bolt into the pilot hole of a hole-saw cutout. Secure the bolt with a washer and nut. Using a hacksaw, cut a 1/4-in. deep slot in line with the bolt. Cut a piece of adhesive-backed sandpaper so that you can slide one end into the slot, wrap it around the cutout, and slide the other end back into the slot. Chuck the bolt into a drill, and you now have a homemade drum sander. — E.R. Comstock. How to Sand Wood Faster
Iron-on edge-banding is a quick way to cover up an edge on plywood. Trimming the excess, however, is tricky. I’ve tried edge-banding trimmers, but I find the results are unpredictable. With the trimmers I’ve tried, it wasn’t easy to change the direction of the cut to suit the grain direction of the edge-banding. If you’re cutting against the grain, you’re likely to tear out a chunk of your new edge-banding. Instead, I use a wide, sharp chisel. This way, I can read the grain direction and trim accordingly. Angle the chisel slightly and go slow, raising the back corner of the chisel just enough so that it doesn’t dig into the plywood veneer. Smooth the corner with a sanding block after trimming. Check out this amazing edge band veneering project!
Building a wine rack is usually a very common beginner's woodworking plan. Creating a wine rack is an easy plan that can most of the time be completed in a day or half, depending on how large and detailed you would like it to be. And the better news is that this free wine rack plan will let you build you a great looking wine rack for much less than it would cost.

Instead of permanently mounting my 6-in. vise to a work-bench, I attached it to scrap plywood so I can clamp it wherever I need it. Stack two pieces of 3/4-in. plywood and screw them together with 1-1/4 in. drywall screws. Mark the vise-mounting holes on the plywood and drill 3/4-in. guide holes through both pieces. Recess the nut by drilling through the bottom sheet with a 1-in. spade bit using the 3/4-in. hole as a guide. Fasten the vise to the plywood with bolts sized to match the vise-mounting holes. If the bolt shafts are too long, cut them off with a hacksaw. — LuAnn Aiu. Plus: Learn how to use vise grips to pull nails.
When cutting full sheets with my circular saw, I use plastic shelving units as sawhorses. The height is just right and by using three of them, I can make cuts in any direction and the plywood is fully supported. And because the shelving units are made of plastic, I can cut right into them without worrying that they’ll damage my saw blade. Plastic shelves are available for $20 at home centers. — John Tinger. Check out these tips for making long cuts with a circular saw.

Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
With the advances in modern technology and the demands of industry, woodwork as a field has changed. The development of Computer Numeric Controlled (CNC) Machines, for example, has made us able to mass-produce and reproduce products faster, with less waste, and often more complex in design than ever before. CNC Routers can carve complicated and highly detailed shapes into flat stock, to create signs or art. Rechargeable power tools speed up creation of many projects and require much less body strength than in the past, for example when boring multiple holes. Skilled fine woodworking, however, remains a craft pursued by many. There remains demand for hand crafted work such as furniture and arts, however with rate and cost of production, the cost for consumers is much higher.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
How do you divide 11-3/8-in. (or any other mathematically difficult number) into equal parts without dividing fractions? Simple. Angle your tape across the workpiece until it reads an easily-divisible dimension and make your marks with the tape angled. For example, say you want to divide an 11-3/8-in. board into three equal parts. Angle the tape until it reads 12-in., and then make marks at “4” and “8”. Plus: More measuring tips and tricks.
×